# CN105 to Grove Wiring: Pinout & Diagram

> Wiring diagram and pinout for connecting an ESP32 (M5Stack) to the Mitsubishi CN105 port via a Grove HY2.0 connector. Every conductor, both connector housings, and the checks to make before power goes back on.

Source: https://serin-labs.com/wiring.html
Last updated: 2026-11-19

![The empty red CN105 serial port on a Mitsubishi indoor unit's control board, with the CN105 label and pins 1 and 5 marked in the silkscreen](https://serin-labs.com/assets/gallery/800/mitsubishi-cn105-port-control-board.webp.webp)

CN105, on the control board of a Mitsubishi indoor unit.

This reference shows every connection between the CN105 service port on a Mitsubishi indoor unit and the Grove HY2.0 connector on an M5Stack Atom S3 Lite or NanoC6. It identifies each conductor, both connector housings, and the checks to complete before restoring power.

Crimp your own from the parts below, or buy the [cable assembled and tested](https://serin-labs.com/cable.html).

## Power and signal connections

The Serin cable is passive: four conductors carry ground, 5 V power, and the two serial signals. CN105 has five positions, but its 12 V position is left empty. The cable supplies the board through Grove. It contains no voltage regulator or level shifter.

On the NanoC6, the board's regulator converts the 5 V input to 3.3 V for the ESP32-C6. It does not convert CN105's 12 V supply to 5 V. This power path is shown in the [M5Stack NanoC6 schematic](https://m5stack-doc.oss-cn-shenzhen.aliyuncs.com/505/Sch_M5NanoC6_v0.0.1.pdf).

**Power voltage and signal tolerance are different.** The same schematic shows Grove's signal pins connected to GPIO1 and GPIO2, with ESD protection diodes but no UART level shifter. Those diodes do not establish 5 V GPIO tolerance. [Espressif specifies a 3.6 V GPIO voltage limit](https://docs.espressif.com/projects/esp-faq/en/latest/hardware-related/hardware-design.html#what-is-the-voltage-tolerance-of-gpios-of-esp-chips). For a custom interface, check the serial signal levels against the board's limits and use suitable level conversion where required. The passive cable does not provide level conversion.

## Reusing an existing Mitsubishi adapter cable

The documented installation uses the Serin cable between the indoor unit's CN105 port and the controller's four-pin Grove socket. A five-pin adapter-end connector labeled CN501 is not a direct Grove connection.

There is no verified CN501-to-Grove conversion pinout in this guide. Do not apply the CN105 cavity numbers below to the adapter end, or identify signals by wire color alone. Reuse would require identifying the exact connector and verifying every conductor, including leaving 12 V disconnected from the controller.

If the indoor unit is difficult to reach, plan access to its control box or have an installer make the standard connection. [Contact support with the adapter and indoor-unit models](https://serin-labs.com/contact.html) before relying on an alternative cable arrangement.

## Wiring diagram

Scroll sideways to see the full diagram.

| Wire | CN105 | Grove | Carries |
| --- | --- | --- | --- |
| Black | 2 · GND | 1 · GND | Ground reference |
| Red | 3 · 5V | 2 · 5V | 5 V from the HVAC |
| White | 4 · TX | 3 · RX · GPIO 2 | HVAC → board |
| Yellow | 5 · RX | 4 · TX · GPIO 1 | Board → HVAC |
| none | 1 · 12V | — | *Leave empty* |

Check before you power it on

1. Unit power is **off** at the breaker before you connect or disconnect the connector.
2. Cavity 1 on the CN105 end is **empty**, and the ▲ lines up with the 1 on the board silkscreen.
3. Black and red are **not swapped**. Reversed power can damage a board.

![The orange Serin CN105-to-Grove cable plugged into the CN105 port on a Mitsubishi MVZ-A18AA7 ducted air handler control board](https://serin-labs.com/assets/gallery/800/serin_cn105_mvz_aa7_1.webp.webp)

The finished cable seated in a real CN105 port, here on a Mitsubishi MVZ-A18AA7 ducted air handler.

![The CN105-to-Grove cable plugged into the CN105 port on the control board of a Mitsubishi wall unit](https://serin-labs.com/assets/gallery/800/serin_cn105_mitsubishi_gl06na.jpg.webp)

The same connection on a wall unit, where the board sits beside it.

## Pinout reference

### CN105 · JST-PAP-05V-S

| Pin | Signal | Description |
| --- | --- | --- |
| 1 | 12V | *Not used* |
| 2 | GND | Ground |
| 3 | 5V | 5V Power |
| 4 | TX | Serial data output from HVAC; see · signal limits |
| 5 | RX | Serial data input to HVAC; see · signal limits |

### Grove · HY2.0-4P Atom S3 Lite, NanoC6

| Pin | Signal | Description |
| --- | --- | --- |
| 1 | G | Ground (connects to ESP32 GND) |
| 2 | 5V | 5V Power (connects to ESP32 5V/VCC) |
| 3 | G2 | RX (connects to ESP32 UART RX pin) |
| 4 | G1 | TX (connects to ESP32 UART TX pin) |

## Build your own

You need two connector housings and four conductors. Crimp the pinout above into these:

- JST PAP-05V-S · CN105 side [DigiKey](https://www.digikey.com/en/products/detail/jst-sales-america-inc/pap-05v-s/759977)
- Grove HY2.0-4P · device side [DigiKey](https://www.digikey.com/en/products/detail/seeed-technology-co-ltd/110990027/5482567)

The [parts list](https://serin-labs.com/parts.html) covers the boards these connect to.

### Safety

Turn off power to the indoor unit at the breaker, not just at the remote, before you connect or disconnect any cable. Leave power off until the cover is back on. CN105 is the only connector you need to handle. The rest of the control board carries line voltage.

![A five-way JST PAP-05V-S connector at the top and a four-way Grove HY2.0-4P connector at the bottom, joined by four wires: yellow, white, red, and black](https://serin-labs.com/assets/content/746/jst_hy20.jpg.abf88bcdf180.webp)

## References

- [SwiCago/HeatPump](https://github.com/SwiCago/HeatPump)
- [Hacking a Mitsubishi Heat Pump (chrdavis)](https://chrdavis.github.io/hacking-a-mitsubishi-heat-pump-Part-1/)
- [CN105 Connector (casualhacker.net)](https://casualhacker.net/post/2017-10-24-CN105_Connector)
- [geoffdavis/esphome-mitsubishiheatpump](https://github.com/geoffdavis/esphome-mitsubishiheatpump)

- [echavet/MitsubishiCN105ESPHome](https://github.com/echavet/MitsubishiCN105ESPHome)
- [akifbayram/mitsubishi-cn105-homekit](https://github.com/akifbayram/mitsubishi-cn105-homekit)
- [muart-group](https://github.com/muart-group)

Ready-made alternative

## Buy the cable assembled

The same harness, built and electrically tested, from $8, in 20 cm and 50 cm. Or take the [Serin Controller](https://serin-labs.com/controller.html), which is an ESP32 board with this cable already attached, from $35.

[CN105 Cable](https://serin-labs.com/cable.html) [Serin Controller](https://serin-labs.com/controller.html)
