# CN105-to-Grove Cable and ESP32 Parts List

> Ready-made CN105-to-Grove cable for Mitsubishi mini-splits, from $8, plus the supported ESP32 boards and the JST part numbers to crimp your own.

Source: https://serin-labs.com/parts.html
Last updated: 2026-11-19

[![The pre-assembled Serin Controller, an M5Stack ESP32 board with the CN105-to-Grove cable attached](https://serin-labs.com/assets/content/800/serin_cn105_controller.jpg.cf751b9c14ef.webp)](https://serin-labs.com/controller.html)

## The pre-assembled option

[5.0 · 67 reviews](https://serin-labs.com/reviews.html)

The [Serin Controller](https://serin-labs.com/controller.html) ships pre-assembled with the CN105 cable included, ready to [flash the firmware of your choice](https://serin-labs.com/flash.html): ESPHome, Apple Home, or Google Home & Alexa compatible. The rest of this page covers building your own.

## 1. CN105-to-Grove cable (required)

This cable connects the ESP32 board to the CN105 service port on a Mitsubishi indoor unit. It uses a JST PAP-05V-S housing at the indoor unit and a Grove HY2.0-4P connector at the ESP32 board. Use the pinout and part numbers in the [wiring reference](https://serin-labs.com/wiring.html#build-your-own) to make your own, or purchase a [ready-made cable](https://serin-labs.com/cable.html#buy-cable) from $8. Choose the 50 cm cable for a ducted air handler. See the [length guide](https://serin-labs.com/cable.html#length) for details.

## 2. ESP32 board (required)

Choose one of the two supported boards. Both work with the ESPHome, Apple Home, and Google Home & Alexa compatible firmware.

### M5Stack NanoC6

Recommended

The smallest supported option, with Wi-Fi 6.

ESP32-C6 · 23.5 × 12 mm

[Buy on Amazon](https://amzn.to/4zLcujm)

### M5Stack Atom S3 Lite

A larger board with a faster dual-core processor.

ESP32-S3 · 24 × 24 mm

[Buy on Amazon](https://www.amazon.com/dp/B0D6S1LD1G?tag=openbin0e-20)

**Detailed spec comparison**

Scroll sideways to read all columns.

|  | NanoC6 | Atom S3 Lite |
| --- | --- | --- |
| **Chip** | ESP32-C6 (RISC-V, 160 MHz) | ESP32-S3 (dual-core, 240 MHz) |
| **Wi-Fi** | Wi-Fi 6 (802.11ax, 2.4 GHz) | Wi-Fi 4 (802.11n, 2.4 GHz) |
| **Size** | 23.5 × 12 × 12.5 mm | 24 × 24 × 13 mm |
| **USB** | USB-C | USB-C |
| **Grove port** | HY2.0-4P | HY2.0-4P |
| **Button** | Yes | Yes |
| **ESPHome** | Full support | Full support |
| **HomeKit** | Full support | Full support |
| **Google Home & Alexa** | Supported | Supported |

The NanoC6 is recommended for most setups: it is smaller and holds a stronger signal inside the sheet metal of HVAC units.

## 3. USB-C data cable (for firmware installation)

This cable is required for the initial [firmware installation](https://serin-labs.com/flash.html). A USB-C cable that supports phone data transfer usually works.

- It must be a **data** cable, not a charge-only cable.
- Test it by connecting a phone. If your computer detects the phone, the cable works.

## Shopping list

| Item | Where to buy |
| --- | --- |
| **CN105-to-Grove Cable** | [Buy ready-made](https://serin-labs.com/cable.html#buy-cable) · or · [DigiKey](https://www.digikey.com/) · (DIY parts) |
| **ESP32 Board** · (NanoC6 or Atom S3 Lite) | [Amazon](https://amzn.to/4zLcujm) · (NanoC6) or · [Amazon](https://www.amazon.com/dp/B0D6S1LD1G?tag=openbin0e-20) · (Atom S3 Lite) |
| **USB-C Data Cable** | Likely already on hand |

### Multiple indoor units

You need **one board and one cable per indoor unit** because each indoor unit has its own CN105 port. A three-zone system requires three boards and three cables.

**Optional accessories**

- **USB-C data cable:** required only for the initial firmware installation. Later updates install over Wi-Fi.
- **Label maker or tape**: helpful for labeling cables in multi-unit installations.
- **USB-C power supply**: for powering the board on a bench to test it before installation.

## Next steps

1. [Check your model](https://serin-labs.com/compatibility.html): type your model number for an instant compatibility answer.
2. [Flash the firmware](https://serin-labs.com/flash.html): install ESPHome, Apple Home, or Google Home & Alexa compatible firmware from your browser.
3. [Connect the cable](https://serin-labs.com/controller/install.html): attach it to the indoor unit.

[Install the firmware](https://serin-labs.com/flash.html)

---

The Amazon links on this page are affiliate links. As an Amazon Associate, Serin Labs earns from qualifying purchases. Other links are provided for convenience and are not affiliate links.
