# Room temperature sensors — Serin Link

> Choose the room temperature source used for heat-pump control with Serin Link. Check sensor availability and understand fallback readings.

Source: https://serin-labs.com/link/room-sensors.html
Last updated: 2026-11-10

**Room Sensor** identifies the temperature source that the controller reports for heat pump control. Other measurements can appear in **About → Details** without controlling the heat pump.

Scroll sideways to read all columns.

| Source name | Meaning |
| --- | --- |
| Internal | The heat pump’s internal room temperature source. |
| Sensor | A remote sensor source supplied by the controller. |
| Link | A temperature source from a paired Serin Link with a sensor. |
| A controller-supplied name | The controller’s name for that source, such as a room name. |

Source names and choices depend on the controller firmware, hardware, and configured sensors.

The built-in sensor on the 1.5-inch kit corrects for electronics heat before sending readings to the controller. See the [sensor reference](https://serin-labs.com/link/technical-reference.html#built-in-sensor-correction) for correction and calibration details.

## Select a temperature source

1. Open **Settings → Room Sensor** and push the knob.
2. Turn to a source; push or tap **Choose** to apply it. Turning alone does not apply a source.
3. Check the source name and status after returning to Settings.

[![Room Sensor ring picker](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/room-source-list.png)](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/room-source-list.png)

Room Sensor ring picker

With touch, tap the Room Sensor icon, then the current-source chip. Tap a source icon to apply it. **Selected** marks the applied source with a valid reading; tapping it confirms that source and returns to Settings.

To leave unchanged, tap **Back**, or turn past the last source and push or tap **Return**. For missing sources or a selection that does not apply, see [Unavailable sensor readings](https://serin-labs.com/link/troubleshooting.html#unavailable-sensor-readings).

## Add or configure a remote sensor

Configure sensors at the controller before selecting them on Serin Link.

For HomeKit-compatible or Matter-compatible controller firmware with a **Room Sensor** card and Bluetooth support:

1. Power a compatible Bluetooth thermometer.
2. Open the [controller web interface](https://serin-labs.com/link/connections.html#open-the-controller-web-interface) and its **Room Sensor** card.
3. Turn on **Enable Remote Sensors**, select **Add Sensor…**, and choose the thermometer from the scan results.
4. Check for a current temperature, then [select the source on Serin Link](https://serin-labs.com/link/room-sensors.html#select-a-temperature-source).

Use **Manage Sensors** in the controller web interface to rename or remove a sensor, or change its calibration offset. The controller firmware supplies these controls. They are not Serin Link settings. See the [controller’s remote sensor instructions](https://github.com/akifbayram/mitsubishi-cn105-homekit#remote-sensor-ble) for compatible sensor types and configuration details.

For ESPHome, configure the remote temperature entity with the [Serin YAML generator](https://serin-labs.com/esphome/generate-yaml.html). Install that configuration as instructed by the generator. Available Serin Link source choices depend on that controller configuration.

For missing or old measurements, see [Unavailable sensor readings](https://serin-labs.com/link/troubleshooting.html#unavailable-sensor-readings).

**Source details**

Source: `serin-link`
Manual: `docs/manual/MANUAL.md`
Source revision: `b354d9ab980d0a1f6ee511b2de4669a8f890b33a`
