# Firmware updates and resets — Serin Link

> Update Serin Link over Wi-Fi, reinstall firmware over USB, or reset settings. Check which procedures preserve settings and controller pairings.

Source: https://serin-labs.com/link/maintenance.html
Last updated: 2026-11-10

Check installed versions in [About and Details](https://serin-labs.com/link/diagnostics.html#about-and-details).

## Update Serin Link

**Update** installs Serin Link firmware and preserves pairings. Controller updates use the controller’s web interface or firmware instructions.

Complete controller Wi-Fi setup first. The Update button requires an online controller that supports sharing update connection details. If it is absent, check those requirements.

For ESPHome configuration and credential-sharing requirements, see [Update connection requirements](https://serin-labs.com/link/maintenance.html#update-connection-requirements).

1. Open **Settings → About → Details → Update**.
2. Wait for **Checking**, then review the offered version.
3. Tap **Install** or push the knob; Install is highlighted initially.
4. Keep Serin Link powered through download, verification, and restart, and for at least 30 seconds afterward.

[![Update checking](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/update-checking.png)](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/update-checking.png)

Update checking

[![Update available](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/update-available.png)](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/update-available.png)

Update available

[![Update download and Cancel control](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/update-download.png)](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/update-download.png)

Update download and Cancel control

To cancel during **Checking** or **Downloading**, tap **Cancel**, push the knob, or hold the knob. On the version-confirmation screen, tap **Cancel**, or turn the knob to highlight **Cancel** and push it. Holding the knob also cancels. A push while **Install** is highlighted starts installation.

The confirmation screen closes after about one minute without a choice. Serin Link returns to Settings. Check for updates again.

During **Verifying** and **Installed / Restarting**, cancellation is unavailable. Wait for Serin Link to restart. If the firmware is current, tap **Done** or push the knob to dismiss **Up to date**.

Check the installed version under **About → Details → LINK**. For an old version returning, a failed reset, or a missing newly paired zone, see [post-update recovery](https://serin-labs.com/link/troubleshooting.html#the-previous-version-returns-after-an-update).

[![Up to date](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/update-uptodate.png)](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/update-uptodate.png)

Up to date

If an update fails, see [Update failure](https://serin-labs.com/link/troubleshooting.html#update-failure).

## Update connection requirements

The standard browser-installed ESPHome build allows Serin Link updates. With a configuration from the YAML generator, enable **Connect a Serin Link** and **Allow Link firmware updates**, then install the configuration. Updates require the controller to share Wi-Fi credentials with Serin Link. See the [ESPHome update reference](https://serin-labs.com/link/technical-reference.html#esphome-updates) for requirements and how to disable sharing.

## Reinstall firmware over USB

The [browser flasher](https://serin-labs.com/flash-link.html) preserves settings and pairings when **Erase everything first** is unchecked. Checking it restores factory state and requires pairing again. Keep USB connected until completion.

For errors, see [USB installation troubleshooting](https://serin-labs.com/link/troubleshooting.html#usb-installation-or-startup-fails).

## Reset Link

Warning

Reset Link erases all Serin Link zone pairings and settings, then restarts. The heat pump keeps running. The controller’s home pairing and Wi-Fi network are not affected.

1. Open **Settings → Advanced**.
2. Highlight **Reset Link**.
3. Keep the knob pushed until the confirmation arc is complete.
4. Release the knob when **Reset Link?** appears.
5. Tap **Reset** to erase Serin Link, or **Cancel** to keep its settings.

Touching **Hold the knob** does not start a reset.

[![Reset Link — hold the knob](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/advanced-reset.png)](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/advanced-reset.png)

Reset Link — hold the knob

[![Reset Link confirmation](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/reset-confirm.png)](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/reset-confirm.png)

Reset Link confirmation

The dialog starts on **Cancel**, so a knob push keeps settings. To erase with the knob, turn to **Reset** and push. Releasing early during the arc cancels before the dialog opens. After reset and restart, [pair again](https://serin-labs.com/link/pairing.html#first-power-on-and-pairing).

Child Lock does not block Reset Link once you reach Advanced. If reset shows **Failed** after an update, follow [post-update recovery](https://serin-labs.com/link/troubleshooting.html#the-previous-version-returns-after-an-update).

Connect power with the knob released to start Serin Link normally.

**Source details**

Source: `serin-link`
Manual: `docs/manual/MANUAL.md`
Source revision: `b354d9ab980d0a1f6ee511b2de4669a8f890b33a`
