# Status and diagnostics — Serin Link

> Check Serin Link and controller versions, sensor readings, connection details, and diagnostic information before contacting support.

Source: https://serin-labs.com/link/diagnostics.html
Last updated: 2026-11-10

Use these details for support; see [Troubleshooting](https://serin-labs.com/link/troubleshooting.html#troubleshooting) for warnings.

## About and Details

Open **Settings → About → Details**. Swipe up or turn the knob to scroll. When available, **Sensor battery · N%** appears with About highlighted.

[![About details](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/about.png)](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/about.png)

About details

At the list’s end, turn further to **Update** or **Back** and push. A push before that, or a tap outside the list, returns to Settings.

**Last boot** turns amber after a crash, watchdog reset, or brownout. **Protocol** turns amber when the Serin Link and controller protocol versions differ.

Scroll sideways to read all columns.

| Section | Information |
| --- | --- |
| LINK | Serin Link firmware, build, board, MAC address, uptime, last restart reason, and wireless protocol versions. |
| CONTROLLER | Serin Controller identity and available firmware, restart, and Wi-Fi details. |
| CONNECTION | The wireless connection between Serin Link and the controller, signal strength, and time since the last message. |
| HEAT PUMP | CN105 connection, available operating details, and reported heat pump faults. |
| SENSOR | Available remote sensor temperature, humidity, battery level, and signal strength. |
| LINK SENSOR | Available temperature and humidity measured by Serin Link’s sensor. |

[![Sensor details with the control source marked](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/about-sensors.png)](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/about-sensors.png)

Sensor details with the control source marked

**IN CONTROL** marks the selected source with a valid reading. Other readings need not control the heat pump. Unsupported fields are absent; a dash means a value is unavailable or has not arrived.

## Contact support

For support, record the selected zone, Serin Link board, both firmware versions, connection status, and any fault code. Include the **Last boot**, **Last seen**, and signal fields when available. Describe the action and message that preceded the problem. Send these details through [Serin support](https://serin-labs.com/contact.html).

## Heat Pump status

[![Heat Pump status](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/advanced-heat-pump.png)](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/advanced-heat-pump.png)

Heat Pump status

**Heat Pump** reports status without adjusting the heat pump:

- **Connected / Not connected:** whether the controller reports CN105 communication.
- **Fault** with a code: a heat pump fault.
- A count such as **3 errors**: communication errors.
- Operating stage, compressor frequency, and outdoor temperature appear when reported by the controller and heat pump.

With multiple zones, push or tap **Press to choose zone**. Selecting a zone returns home; reopen Advanced to inspect its Heat Pump status.

## About this manual

Your firmware version can be different from the version that this manual describes.

**Source details**

Source: `serin-link`
Manual: `docs/manual/MANUAL.md`
Source revision: `b354d9ab980d0a1f6ee511b2de4669a8f890b33a`
