# Temperature, modes and airflow — Serin Link

> Use Serin Link to adjust target temperature, heating and cooling modes, fan speed, and vane direction for the selected room.

Source: https://serin-labs.com/link/controls.html
Last updated: 2026-11-10

Use these controls for the selected room. To operate another room, [select its zone](https://serin-labs.com/link/zones.html#zones-more-than-one-room) first.

## The home screen

[![Home screen during heating](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/home-heat.png)](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/home-heat.png)

Home screen during heating

- **Target temperature:** turn the knob, slide along the ring, or tap the left side to decrease and the right side to increase by one step. Serin Link sends the change when you stop.
  [![Target temperature changes as the knob turns](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/anim-turn-setpoint.png)](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/anim-turn-setpoint.png)
  Target temperature changes as the knob turns
  First-use tips do not change the heat pump. Changes made in a home app or with the remote appear when the controller reports them; turn the knob to choose another target, including one used earlier.
- **Ring markers:** the bright marker is the target; the smaller marker is the room temperature. The joining arc turns grey when the heat pump is off.
- **Status:** shows operation such as *Heating* or *Cooling*, or the mode when idle. Tap it to choose a mode. **Offline**, **Syncing**, and other warnings are explained in [Troubleshooting](https://serin-labs.com/link/troubleshooting.html#troubleshooting).
- **Now:** measured room temperature and humidity.
- **Fan button:** opens [Airflow](https://serin-labs.com/link/controls.html#airflow). With multiple zones, the zone name replaces it. A warning label temporarily replaces either.

[![Home screen during cooling](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/home-cool.png)](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/home-cool.png)

Home screen during cooling

In **Heat/Cool** mode, the heat pump keeps the room temperature between two limits. The home screen shows both temperatures.

1. Tap the temperature that you want to change. The low limit is selected until you tap the high limit.
2. Turn the knob to change the selected temperature. Alternatively, tap near the top or bottom of the left edge to decrease it, or of the right edge to increase it.

[![Heat/Cool mode with two temperature limits](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/home-band.png)](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/home-band.png)

Heat/Cool mode with two temperature limits

[![Off](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/home-off.png)](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/home-off.png)

Off

## Choosing a mode

1. Open the mode selection screen from the Menu or tap the status label on the home screen.
2. Turn the knob to highlight a mode.
3. Push the knob, tap **Use mode**, or tap the mode icon to select that mode.

[![Mode selection screen](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/mode-picker.png)](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/mode-picker.png)

Mode selection screen

Select **Back**, then push the knob or tap **Return** to leave unchanged. Tapping the Back ring icon also returns directly.

Some controllers offer both **Heat/Cool** (a temperature range, shown with flame and snowflake icons) and **Auto** (the controller’s automatic mode).

With Serin HomeKit-compatible and Matter-compatible controller firmware, the controller’s **Auto** mode appears as **Heat/Cool** on Serin Link. The lower temperature is the heating limit; the upper temperature is the cooling limit. These are the same limits used by the home app and controller web interface. The controller keeps at least 2 °C between them.

To stop heat pump operation, select **Off** from the mode selection screen. There is no separate power button.

## Airflow

Flick up on the home screen or tap the fan button. Available controls depend on the heat pump: fan speed and vanes that direct airflow.

[![Airflow](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/airflow.png)](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/airflow.png)

Airflow

Airflow opens with the first control ready to adjust: turning the knob changes its value. With one control, push the knob to leave. With several:

1. Push to leave adjustment mode.
2. Turn to another control and push to select it.
3. Turn to change its value; push to leave adjustment mode.

- **Fan speed:** slide along the center bar or turn the knob in adjustment mode. The filled area shows the speed. Tap the active control to switch between Auto and manual speed, if supported; turning below the lowest speed also selects Auto. Tapping an inactive control first selects it.
- **Vanes:** slide up/down on the vertical vane or left/right on the horizontal vane. Or tap a tile to select it, then turn the knob or tap again to cycle positions.
- **Vane Auto and Swing:** on the vertical vane, Auto is above the highest position and Swing below the lowest. On the horizontal vane, both follow the right position. These options appear only when supported.

**Auto** lets the heat pump control fan speed or vane position. The control dims and shows **AUTO**:

[![Fan on Auto](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/airflow-fan-auto.png)](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/airflow-fan-auto.png)

Fan on Auto

[![Vane on Auto](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/airflow-vane-auto.png)](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/airflow-vane-auto.png)

Vane on Auto

For ESPHome controllers, fan **Auto** appears only when the configured climate supports automatic fan speed. A climate’s fan **On** setting alone does not provide this option.

To leave, flick down outside the tiles, hold the knob to return home, or select **Back** and push the knob or tap **Return**. Turn away from Back to resume adjustment.

[![Airflow with Back highlighted](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/airflow-return.png)](https://serin-labs.com/assets/link/manual/b354d9ab980d0a1f6ee511b2de4669a8f890b33a/figures/airflow-return.png)

Airflow with Back highlighted

**Source details**

Source: `serin-link`
Manual: `docs/manual/MANUAL.md`
Source revision: `b354d9ab980d0a1f6ee511b2de4669a8f890b33a`
