# Serin Link: Rotary Knob Display for Mini Splits

> A wireless dial and temperature sensor for your Serin Controller or compatible ESPHome climate device. Everyday control works without home Wi-Fi.

Source: https://serin-labs.com/link.html
Last updated: 2026-11-19

![A render of the Serin Link in orange, seen from the front and slightly to one side: a round black display tilted back in a flared orange base, its screen reading 72 degrees with Heating above it](https://serin-labs.com/assets/serin-link-v5-34-orange.webp)

![A render of the Serin Link with a black housing that matches the display bezel](https://serin-labs.com/assets/serin-link-v5-34-black.webp)

![A generated bedroom scene with a black Serin Link on a wooden bedside table beside a phone and succulent, its screen displaying Heating and 72 degrees, with a mini-split above the bed](https://serin-labs.com/assets/serin-link-nightstand.webp)

![A render of the Serin Link head-on, the round face filling the frame: 72 degrees in large type with Heating above it and the target arc drawn on the rim](https://serin-labs.com/assets/serin-link-v5-front.webp)

![A render of the Serin Link from the left: the display tilted back at 45 degrees on a wedge-shaped orange base, with a round sensor vent low in the side of the base](https://serin-labs.com/assets/serin-link-v5-left.webp)

![An exploded view of the Serin Link from below: the black display module, the orange base lifted off the sensor board with its USB-C port, and the foot beneath](https://serin-labs.com/assets/serin-link-exploded.webp)

![The Serin Link in orange standing beside a smartphone lying face down, the Link about half the phone's length across](https://serin-labs.com/assets/serin-link-phone-scale.webp)

![What comes in the box: the Serin Link in orange, a white USB-C power adapter, and a coiled white USB-C cable](https://serin-labs.com/assets/serin-link-in-the-box.webp)

![Orange printed stand, black bottom cap, sensor PCB, four screws, Allen key, and silicone pad laid out on white](https://serin-labs.com/assets/serin-link-build-kit-contents.webp)

![Black printed stand and bottom cap, sensor PCB, four screws, Allen key, and silicone pad laid out on white](https://serin-labs.com/assets/serin-link-build-kit-black.webp)

![A render of the print-your-own kit: sensor PCB, four screws, Allen key, and silicone pad, with the stand and bottom cap shown as wireframes](https://serin-labs.com/assets/serin-link-print-your-own.webp)

![Front and back of the Serin Link sensor PCB with USB-C port and display connector](https://serin-labs.com/assets/serin-link-pcb.webp)

# Serin Link

$180

Pairs with a Serin Controller New

Link pairs wirelessly with a Serin Controller, which plugs into your mini-split. Their direct radio connection carries controls and temperature readings without home Wi-Fi. Select Link's built-in temperature sensor so heating and cooling use the temperature where you sit.

## Assembled Link

Orange $180

[Buy](https://shop.serin-labs.com/cart/52705909965080:1?ref=serin-direct)

**Free US shipping**

Free US shipping on orders $35 and up, from New Jersey. Ships to US addresses only.

For orders below $35, shipping is calculated at checkout. [Shipping policy](https://serin-labs.com/policies.html#shipping).

**30-day returns**

30-day returns by mail. [How returns work](https://serin-labs.com/policies.html#returns).

**1-year warranty**

1-year limited hardware warranty against manufacturing defects. [Warranty terms](https://serin-labs.com/warranty.html).

Ships within 1–3 days

Secure checkout by Shopify, shipped from New Jersey.

- [Serin Link, Orange: $180](https://shop.serin-labs.com/cart/52705909965080:1?ref=serin-direct)
- [Serin Link, Orange, with Controller: $200 after automatic discount](https://shop.serin-labs.com/cart/52705909965080:1,52441459360024:1?ref=serin-direct)
- [Serin Link, Black: $180](https://shop.serin-labs.com/cart/52705909997848:1?ref=serin-direct)
- [Serin Link, Black, with Controller: $200 after automatic discount](https://shop.serin-labs.com/cart/52705909997848:1,52441459360024:1?ref=serin-direct)

## Serin Link DIY Kit

Printed stand, Orange Display sold separately $60

[Buy](https://shop.serin-labs.com/cart/52928918028568:1?ref=serin-direct)

**Free US shipping**

Free US shipping on orders $35 and up, from New Jersey. Ships to US addresses only.

For orders below $35, shipping is calculated at checkout. [Shipping policy](https://serin-labs.com/policies.html#shipping).

**30-day returns**

30-day returns by mail. [How returns work](https://serin-labs.com/policies.html#returns).

**1-year warranty**

1-year limited hardware warranty against manufacturing defects. [Warranty terms](https://serin-labs.com/warranty.html).

Ships in 1–2 days

Secure checkout by Shopify, shipped from New Jersey.

- [Serin Link DIY Kit, Printed stand, Orange: $60](https://shop.serin-labs.com/cart/52928918028568:1?ref=serin-direct)
- [Serin Link DIY Kit, Printed stand, Orange, with Controller: $95](https://shop.serin-labs.com/cart/52928918028568:1,52441459360024:1?ref=serin-direct)
- [Serin Link DIY Kit, Printed stand, Orange with USB cable + power adapter: $70](https://shop.serin-labs.com/cart/52928918094104:1?ref=serin-direct)
- [Serin Link DIY Kit, Printed stand, Orange with USB cable + power adapter, with Controller: $105](https://shop.serin-labs.com/cart/52928918094104:1,52441459360024:1?ref=serin-direct)
- [Serin Link DIY Kit, Printed stand, Black: $60](https://shop.serin-labs.com/cart/52928918159640:1?ref=serin-direct)
- [Serin Link DIY Kit, Printed stand, Black, with Controller: $95](https://shop.serin-labs.com/cart/52928918159640:1,52441459360024:1?ref=serin-direct)
- [Serin Link DIY Kit, Printed stand, Black with USB cable + power adapter: $70](https://shop.serin-labs.com/cart/52928918225176:1?ref=serin-direct)
- [Serin Link DIY Kit, Printed stand, Black with USB cable + power adapter, with Controller: $105](https://shop.serin-labs.com/cart/52928918225176:1,52441459360024:1?ref=serin-direct)
- [Serin Link DIY Kit, Print your own: $50](https://shop.serin-labs.com/cart/52928917995800:1?ref=serin-direct)
- [Serin Link DIY Kit, Print your own, with Controller: $85](https://shop.serin-labs.com/cart/52928917995800:1,52441459360024:1?ref=serin-direct)
- [Serin Link DIY Kit, Print your own with USB cable + power adapter: $60](https://shop.serin-labs.com/cart/52928918061336:1?ref=serin-direct)
- [Serin Link DIY Kit, Print your own with USB cable + power adapter, with Controller: $95](https://shop.serin-labs.com/cart/52928918061336:1,52441459360024:1?ref=serin-direct)
- [Serin Link DIY Kit, Print your own: $50](https://shop.serin-labs.com/cart/52928918126872:1?ref=serin-direct)
- [Serin Link DIY Kit, Print your own, with Controller: $85](https://shop.serin-labs.com/cart/52928918126872:1,52441459360024:1?ref=serin-direct)
- [Serin Link DIY Kit, Print your own with USB cable + power adapter: $60](https://shop.serin-labs.com/cart/52928918192408:1?ref=serin-direct)
- [Serin Link DIY Kit, Print your own with USB cable + power adapter, with Controller: $95](https://shop.serin-labs.com/cart/52928918192408:1,52441459360024:1?ref=serin-direct)

## Requirements

Link encrypted radio Controller CN105 cable Indoor unit

A [Serin Controller](https://serin-labs.com/controller.html) at each indoor unit you want to control, or an ESPHome climate device with the `serin_link` component.

No soldering required

## Build your own Link

The PCB arrives assembled and tested. Fit the parts together, connect the display, and install the firmware.

![Exploded view of the Serin Link display, printed stand, sensor PCB, bottom cap, and silicone pad](https://serin-labs.com/assets/content/800/serin-link-exploded-side.webp.70fc8f912f21.webp)

Display purchased separately.

1. ### Get the display
  Buy the supported VIEWE 1.5-inch module separately.
2. ### Assemble the kit
  Install the display and PCB, then fit the cap and pad.
3. ### Install the firmware
  Flash over USB with a supported desktop browser.

[Read the build guide](https://serin-labs.com/link/build-guide.html)

## Overview

Highlights

Room for the things around it.

About 2 inches wide and 2½ inches tall, Link fits neatly beside a laptop or bedside lamp.

A quieter screen at night.

Keep a dim temperature reading visible, or set the screen to turn off when idle. The first touch or turn wakes it without changing your settings.

The interface

### A turn is all it takes.

Adjust the temperature from your desk or bedside without reaching for your phone. Press the knob for mode and fan controls, or use the touchscreen. Link only shows the modes and fan speeds your unit supports.

![The Serin Link home face in Heating: the knob raises the target from 72 to 75 degrees and back](https://serin-labs.com/assets/fig-home-heat.gif)

Home: turn to set the temperature

![The Serin Link menu: a ring of shortcuts, the highlight stepping from one to the next](https://serin-labs.com/assets/fig-menu.gif)

Menu: turn to highlight, press to open

![The Serin Link airflow screen: fan speed dragged, then the vane stepped through its positions](https://serin-labs.com/assets/fig-airflow.gif)

Airflow: fan speed and vent direction

![The Serin Link mode picker: heat, cool, auto, dry, fan and off around the ring](https://serin-labs.com/assets/fig-mode-picker.gif)

Modes: only the ones your unit has

![The Serin Link glance face: just the room temperature, dim on black](https://serin-labs.com/assets/fig-idle-glance.png)

Dimmed temperature display

Built-in room sensor

### Measure the temperature beside you.

Place Link at your desk or bedside and select it as your Serin Controller's room sensor. Your heat pump then uses the temperature measured there to guide heating and cooling.

Temperature and humidity

Check both readings on Link's display.

Direct to your controller

Sensor readings travel over an encrypted radio connection, without relying on your home Wi-Fi.

![An exploded view of the Serin Link from below: the black display module, the orange base, the sensor board with its USB-C port, and the foot](https://serin-labs.com/assets/content/660/serin-link-exploded-crop.webp.7f84a912d3a1.webp) ![The Serin Link on a bedside table, reading 72 degrees with the room at 70](https://serin-labs.com/assets/serin-link-nightstand.webp)

### Works with Home Assistant

With a compatible ESPHome controller, view Link's temperature and humidity in Home Assistant and use the readings in your automations.

[Explore the ESPHome integration](https://serin-labs.com/esphome/features.html#controls)

## Technical

**Display**

VIEWE 1.5″ UEDX46460015-MD50ET round AMOLED, 310 ppi, capacitive touch

**Controls**

Turn or press the knob; tap, drag, swipe, or hold on the touchscreen

**Wireless**

ESP32-S3 with a dedicated encrypted radio link straight to the controller

**Sensor**

Sensirion SHT41 temperature + humidity, accounts for heat generated inside the device

**Power**

USB-C, no battery

**Pairing limits**

Up to 7 controllers per Serin Link; up to 4 Serin Links per controller

**Works with**

Serin Controller, or any ESPHome climate device with the `serin_link` component

**Firmware**

Free and open source (GPL-3.0); flashable from Chrome or Edge over USB

**Dimensions**

About 2 inches wide, 2½ inches tall, 2 inches deep

**Placement**

Desktop stand, indoor use only

![Serin Link on its compact tabletop stand, viewed from the front](https://serin-labs.com/assets/gallery/800/serin-link-v5-front.webp.webp)

Dimensions About 2 inches wide, 2½ inches tall, and 2 inches deep.

![Front and back of the Serin Link's oval sensor board: USB-C port, display connector, and the SHT41 sensor behind slots in the copper](https://serin-labs.com/assets/serin-link-pcb.webp)

The sensor board Slots in the board reduce heat transfer to the room sensor.

## In the box

![The Serin Link in orange with its USB-C power adapter and coiled USB-C cable](https://serin-labs.com/assets/serin-link-in-the-box.webp)

- Serin Link
  1.5″ touchscreen, rotary knob, and stand with the sensor board inside. Firmware installed.
  1×
- USB-C cable
  Powers the Link; there is no battery.
  1×
- USB power adapter
  1×
- Serin Controller optional
  Standard 8-inch cable. Needed at each indoor unit the Link will control.

The body is 3D printed.

![Orange printed-stand DIY kit contents](https://serin-labs.com/assets/serin-link-build-kit-contents.webp)

### Your DIY kit

- Serin Link PCB
  Assembled and tested. Includes the SHT41 temperature and humidity sensor.
  1×
- Stand + bottom cap, or STL file
  Choose printed parts or the file when ordering.
  1 set
- M2.5 × 8 mm screws
  Three for the display, one for the PCB.
  4×
- Ball-end Allen key
  The tool for assembly.
  1×
- Silicone bottom pad
  Precut, self-adhesive, and reusable.
  1×

**You’ll also need**

The supported VIEWE display , a compatible controller, and a computer for firmware installation.  [View parts and requirements →](https://serin-labs.com/link/build/parts-and-tools.html)

## Add-ons

### [Serin Controller](https://serin-labs.com/controller.html?length=20&braided=no&sensor=no)

Connect a compatible Mitsubishi mini-split to your smart home. Includes a CN105-to-Grove cable.

From $35.00

[Select](https://serin-labs.com/controller.html?length=20&braided=no&sensor=no)

### [Remote Temperature Sensor](https://serin-labs.com/sensor.html)

Room temperature and humidity sensor for your Serin Controller.

$20.00

[View](https://serin-labs.com/sensor.html)

## FAQ

**Does it need Wi-Fi?**

Not for everyday use. The Serin Link connects wirelessly to the controller without using your home Wi-Fi. The controller uses Wi-Fi for updates and remote features. You can use the Serin Link to help connect the controller to Wi-Fi or change its network.

**What does it need at the heat pump?**

A [Serin Controller](https://serin-labs.com/controller.html) at each indoor unit, or an ESPHome climate device running the `serin_link` component. The Serin Link does not talk to the heat pump directly.

**Is it a thermostat?**

It provides temperature controls and a room sensor, but it needs a separate controller to operate the heat pump. The Serin Link shows the current settings and lets you change them. Changing the target temperature on the Serin Link also updates it in your smart home app, and vice versa.

**How do I switch between rooms?**

Swipe left or right on the home screen to switch rooms. To open the room list, press and hold the knob or tap the room name.

**Does it stay lit at night?**

When idle, the screen shows a dim room temperature reading. You can set it to turn off instead. The first touch, knob turn, or knob press wakes the screen without changing any settings.

**Can I install the firmware myself?**

The assembled Serin Link arrives with firmware installed. For the DIY kit, assemble the kit with your separately purchased VIEWE 1.5-inch display, then install the free, open-source firmware through the [Serin Link browser flasher](https://serin-labs.com/flash-link.html). Use Chrome, Edge, or Brave on a computer and connect with a USB data cable. See the [build guide](https://serin-labs.com/link/build-guide.html) for the steps.

### Limitations

- The Link does not operate a heat pump on its own. It needs a [Serin Controller](https://serin-labs.com/controller.html) at each indoor unit, or an ESPHome climate device running the `serin_link` component.
- Up to 7 controllers per Link, and up to 4 Links per controller.
- USB-C powered with no battery; it stays where it is plugged in.
- Indoor use only, on a desktop stand.

After it arrives

## Plug in, pair, and place

Power it over USB-C, press the knob to pair with your controller, then set it where you sit.

[Read the manual](https://serin-labs.com/documentation.html#serin-link) [Quick start](https://serin-labs.com/link/manual.html)
