# CN105 HomeKit-Compatible Controller for Mitsubishi

> Add a Mitsubishi mini-split to Apple Home and Siri with free, open-source HomeKit-compatible firmware on a CN105 ESP32 controller. Local control with no bridge or cloud account.

Source: https://serin-labs.com/homekit/features.html
Last updated: 2026-11-19

The Serin Controller plugs into a service port inside your Mitsubishi indoor unit. Install the free, open-source HomeKit-compatible firmware once from a computer, then pair it with the Apple Home app.

**From $35**

[5.0 · 67 reviews](https://serin-labs.com/reviews.html)

Check my Mitsubishi model [View controller](https://serin-labs.com/controller.html?length=20&braided=no&sensor=no)

You need a computer with Chrome, Edge or Brave to install the firmware, and an iPhone or iPad. What you need

![A CN105 cable plugged into the control board inside a Mitsubishi MSZ-GL06NA indoor unit](https://serin-labs.com/assets/content/800/serin-cn105-cable-connected-msz-gl06na.webp.a0c9c8ac7920.webp) CN105 port

![The Serin Controller with the 50 cm cable in orange braided sleeving, coiled beside the board](https://serin-labs.com/assets/serin-controller-50cm-braided-cable.webp) Serin Controller

![A real Apple Home thermostat screen for the mini-split, set to cool to 76 degrees, with the room at 73 degrees and the fan at 100 percent](https://serin-labs.com/assets/mitsubishi-mini-split-apple-home-thermostat-control.webp) Apple Home app

Installed in an MSZ-GL06NA.

- Control from the Apple Home app and Siri
  Set the temperature and mode in the app, by voice, or from a scene or automation.
- No bridge, server or Mitsubishi account
  The firmware is free and open source, and your phone talks to the controller over your home network.
- One controller per indoor unit
  Start with one room and add more later.

## Check your model first

Enter your Mitsubishi Electric indoor unit’s model number. The result shows whether it is supported and anything to confirm before you order.

[Browse all compatibility information](https://serin-labs.com/compatibility.html)

**Where do I find my model number?**

Look for the model label on your indoor unit, often on the right side or behind the front panel. Use the model number, not the serial number or the number on the remote.

[See the model and port guide](https://serin-labs.com/compatibility.html#how-to-check)

Check model opens the full compatibility guide. Interactive model results require JavaScript.

## What Apple Home can control

The mini-split appears in Apple Home as a thermostat.

### Siri, scenes and automations

Ask Siri for a temperature or a mode, or add the thermostat to a scene or an automation beside your lights and locks. Automations run on an Apple Home hub, so they keep working while you are away.

### A sensor where you sit

An optional Bluetooth thermometer can supply the room temperature instead of the sensor near the ceiling. It appears in Apple Home with temperature, humidity and a low-battery warning.

Vane direction, dry mode and diagnostics are not shown in Apple Home. Use the controller’s web interface for those.

[Explore the controller’s web interface](https://serin-labs.com/controller/web-interface.html)

![A real Apple Home thermostat screen for the mini-split, set to cool to 76 degrees, with the room at 73 degrees and the fan at 100 percent](https://serin-labs.com/assets/mitsubishi-mini-split-apple-home-thermostat-control.webp)

- **Room temperature** Measured inside the unit, or by an optional Bluetooth room sensor.
- **Fan speed** Shown as a percentage beside the room temperature.
- **Target temperature** Set it on the dial, with Siri, or from a scene.
- **Mode** Heat, Cool, Auto, or off, named above the target.

The Apple Home thermostat screen for the mini-split.

## What you need

In order, from the indoor unit to the app on your phone.

1. ### A compatible Mitsubishi indoor unit
  Check the full model number. You need one controller for each indoor unit, and its CN105 port must be free.
  [Find your model number](https://serin-labs.com/compatibility.html#how-to-check)
2. ### Serin Controller
  An ESP32 board for the CN105 port, sold with its cable from **$35**. It arrives without firmware installed. Install the firmware once from a computer with Chrome, Edge or Brave and a USB data cable.
  [Open the browser installer](https://serin-labs.com/flash.html?platform=homekit)
3. ### Your 2.4 GHz Wi-Fi network
  The controller joins your home network and your phone reaches it there. Enter the network name and password from the browser installer, or join the controller’s own setup network, Serin-XXXX, from your phone.
  [See how to join Wi-Fi](https://serin-labs.com/homekit/setup.html#wifi)
4. ### An iPhone or iPad with the Home app
  The mini-split appears as a thermostat, in the app and to Siri. At home, your phone controls it directly. Remote access and automations require an Apple Home hub such as an Apple TV or HomePod.
  See what it can control

## How setup works

The firmware installation takes about two minutes. Turn off the power at the breaker before connecting the cable.

![An orange CN105 cable routed into the electrical compartment of a Mitsubishi wall-mounted indoor unit](https://serin-labs.com/assets/gallery/800/serin-cn105-cable-installed-wall-unit.webp.webp)

Shown on a Mitsubishi wall unit.

1. ### Install the free firmware
  Connect the controller to your computer with a USB data cable and open the browser installer. It installs the HomeKit-compatible build and can enter your Wi-Fi details at the same time.
2. ### Connect it inside the indoor unit
  Turn off the power at the breaker and open the indoor unit’s cover. The CN105 connector is a small five-pin plug on the control board, usually red. Connect the cable, replace the cover, and restore power.
  [The wiring guide shows both ends](https://serin-labs.com/wiring.html)
3. ### Add it to Apple Home
  With your phone on the same Wi-Fi as the controller, open its web interface and scan the pairing QR code in its HomeKit panel, or enter the setup code in the Home app. Confirm the uncertified-accessory notice and assign the thermostat to its room.
  [The setup guide shows each screen](https://serin-labs.com/homekit/setup.html#pair)

[Read the full setup guide](https://serin-labs.com/homekit/setup.html)

If you prefer not to open the unit, share the [wiring guide](https://serin-labs.com/wiring.html) with your HVAC installer.

## Limits to know before you buy

Unsure how one of these applies to your setup? [Ask us before you order](https://serin-labs.com/contact.html)

- ### The firmware is not Apple-certified
  The HomeKit-compatible firmware is an independent open-source project built on Espressif’s HomeKit SDK, credited on the licenses page. It is not an Apple-certified accessory, so the Home app shows a one-time notice that the accessory is uncertified when you add it. Choose Add Anyway to continue.
- ### Apple Home shows a thermostat only
  Apple Home shows power, Heat, Cool, Auto, the target temperature and fan speed. Use the controller’s web interface for dry mode, fan-only mode, vane direction, room sensor settings and diagnostics.
- ### The controller needs the CN105 port to itself
  It cannot share that connection with a factory Wi-Fi adapter or wired wall controller, so it replaces a Kumo Cloud adapter rather than working beside it. CN105 splitters do not work. Your handheld remote is unaffected.

## Compare your options

[Read the full comparison](https://serin-labs.com/blog/mitsubishi-mini-split-apple-home-homekit-siri.html)

Route What you get What it depends on Link

### Serin Controller

Control from the Apple Home app and Siri over your home network, without a server or a Mitsubishi account.

Depends onRequires a one-time firmware install. Remote access and automations need an Apple Home hub.

See what you need

### Already have Kumo Cloud?

Kumo Cloud has no Apple Home support of its own. Homebridge with a Kumo plugin can bridge the adapter into Apple Home, which keeps the adapter and the account and adds a computer running Homebridge.

Depends onUses Mitsubishi’s cloud service and an always-on Homebridge server. The Serin Controller would replace that adapter on the same port, so it is one or the other.

[Compare the three routes](https://serin-labs.com/blog/mitsubishi-mini-split-apple-home-homekit-siri.html#three-ways-to-get-a-mitsubishi-into-apple-home)

### Already use Home Assistant?

Use ESPHome on the controller for the full mini-split feature set in Home Assistant, then expose it to Apple Home through Home Assistant’s HomeKit Bridge.

Depends onHome Assistant must run around the clock. Apple Home shows the same uncertified-accessory notice when it pairs with the bridge.

[Explore ESPHome](https://serin-labs.com/esphome/features.html)

![The Serin Controller with the 50 cm cable in orange braided sleeving, coiled beside the board](https://serin-labs.com/assets/gallery/800/serin-controller-50cm-braided-cable.webp.webp)

## Order the Serin Controller

The controller and cable arrive assembled, without firmware. Install the free firmware, connect it inside your indoor unit, and add it to Apple Home.

**From $35** Free US shipping

[Choose your controller](https://serin-labs.com/controller.html?length=20&braided=no&sensor=no)

Need a hand choosing? [Ask us about your setup.](https://serin-labs.com/contact.html)

Already have a board? [Install the free firmware](https://serin-labs.com/flash.html?platform=homekit) or [open the setup guide](https://serin-labs.com/homekit/setup.html).
