# Serin Controller setup for Home Assistant

> Connect a Mitsubishi mini-split to Home Assistant with Serin Controller and ESPHome firmware. Join Wi-Fi, adopt the controller, and add the integration.

Source: https://serin-labs.com/esphome/setup.html
Last updated: 2026-11-10

Connect your Serin Controller to Wi-Fi and add it to Home Assistant using **ESPHome firmware**.

Different firmware? [Choose your guide](https://serin-labs.com/controller/firmware.html).

**Continue an existing setup**

- **Not installed in the indoor unit yet?** Install it in the indoor unit.
- **Installed, but not on Wi-Fi?** Join your home network.
- **Wi-Fi connected, but not added to Home Assistant?** Add your controller to your app.
- **Already added and installed?** Check that the unit responds.

## Before you start

- A compatible indoor unit and controller with **this guide's firmware installed**. If the firmware is not installed yet, use the [flash tool](https://serin-labs.com/flash.html?platform=esphome) on a computer with a USB-C data cable.
- A 2.4 GHz home Wi-Fi network and its password.
- Home Assistant and the ESPHome dashboard (available as the ESPHome add-on).

## 1 Install the controller

Warning

**Power off at the breaker.** Leave it off while the unit is open. Disconnect USB before connecting CN105.

Follow the [installation guide](https://serin-labs.com/controller/install.html) to connect the CN105 cable, position the controller, and replace the cover before you restore power.

## 2 Join your home Wi-Fi

**Already connected in the flash tool?** Continue to app setup.

1. On your phone, join **serin-XXXXXX**, using the password `serinlabs`. The suffix is unique to your controller.
2. The setup page opens. If it does not, browse to `http://192.168.4.1` while still connected to the controller's setup network.
3. Enter your home Wi-Fi name and password. The controller saves them and restarts on your network.
4. Reconnect your phone to the home network. If you need the controller's IP address, check the router's connected-device list.

**Another way to join Wi-Fi, or a missing setup network**

You can also enter the controller's Wi-Fi details from a computer [over USB](https://serin-labs.com/controller/recovery.html#reset) using the [flash tool's Wi-Fi option](https://serin-labs.com/flash.html). You do not need to reinstall firmware just to change the network. If the setup network does not appear, use [Wi-Fi troubleshooting](https://serin-labs.com/troubleshooting.html#ap-missing).

## 3 Add to Home Assistant

**Already adopted and added to Home Assistant?** Check control.

1. Open the ESPHome dashboard in Home Assistant. With the add-on installation, it is under **Settings > Add-ons > ESPHome**.
2. Find the controller's **Discovered** tile and select **Adopt**. Give it a name such as `living-room`.
3. Select **Install** to build and send the personalized configuration over Wi-Fi. The first build takes a few minutes.
4. In Home Assistant, open **Settings > Devices & services** and configure the discovered ESPHome integration. If you already added it during flashing, use that existing integration.

Discovery requires the controller and Home Assistant to be reachable on the same local network with mDNS allowed. If no device appears, see [ESPHome discovery troubleshooting](https://serin-labs.com/troubleshooting.html#esphome).

After adoption, [customize ESPHome](https://serin-labs.com/controller/customize-esphome.html) to add sensors or diagnostics while preserving the device's credentials.

## 4 Check that the unit responds

1. Check that the app reports the room temperature.
2. Change the mode or target temperature and confirm the indoor unit responds.

If the app connects but commands have no effect, use [the CN105 checks](https://serin-labs.com/troubleshooting.html#hvac-no-response). App pairing does not verify the cable's data connection.

Once control works, [set up a room sensor](https://serin-labs.com/controller/room-sensors.html#placement) or [configure Auto mode](https://serin-labs.com/controller/web-interface.html#auto-mode). The [update](https://serin-labs.com/controller/updates.html) and [Wi-Fi and reset](https://serin-labs.com/controller/maintenance.html) guides cover later maintenance.
